 | |  | |  |
| 94-95 Mustang Air Intake System |
| MAC PRODUCTS |
This kit will install in minutes with a few basic tools.
Complete with:
Complete with:
- All necessary hardware
- Special silicone hoses
- Stainless steel clamps
- MAC's high flow reusable air filter
1994-1995 5.0L Mustang
Air Chamber System includes:
Comes with calibration, our mass air meters are CNC machined 6061 Billet Aluminum.
Plus the highest quality and most reasonably priced. MAC air meter systems are the
best you can use! With calibration tubes you can change calibration for different size
injectors in minutes. There is no need to send anywhere to recalibrate.
- 76MM Billet Aluminum Mass Air Meter
- Lifetime Big Mouth Filter
- Racers Choice Velocity Stack
- Polished Stainless Steel Air Chamber
- Air Tube forward System
Comes with calibration, our mass air meters are CNC machined 6061 Billet Aluminum.
Plus the highest quality and most reasonably priced. MAC air meter systems are the
best you can use! With calibration tubes you can change calibration for different size
injectors in minutes. There is no need to send anywhere to recalibrate.
- MAC's Big Mouth Filter with Velocity Stack
- Billet 76mm Mass Air
- MAC Silicone Connectors
- Stainless Steel Clamps
MAC the first to introduce the Velocity Stack combined
with the "Big Mouth" 6" outlet High Flow filter system.
The Polished Stainless Steel Shroud not only
eliminates effects from fan turbulence, but allows the airflow from outside to go directly
into the filter system. The Velocity Stack, by Design forces intake air to move at
Higher Rate of Velocity & greater CFM to your intake. MAC's Cold Air Induction fits to
stock air box location.
|
76 mm system with calibration CT 8 5.0 and Cobra for stock
injectors. Fits to stock air tube and has removable Billet
aluminum adapter ring to fit aftermarket intakes. This mass air
will fit aftermarket flange less systems.
injectors. Fits to stock air tube and has removable Billet
aluminum adapter ring to fit aftermarket intakes. This mass air
will fit aftermarket flange less systems.
|
94-95 5.0 Mass Air Flow Housing
|
| C&L Performance |
| 73MM |
|
| 76MM |
|
| 73MM Air Induction System |
We are proud to offer a complete Mass Airflow package
designed for 1994-1995 Mustang 5.0L and 1994-2004 V6
3.8L Mustangs. With 700 CFM of airflow, compared to only
550 CFM of the stock unit it replaces, it has been dyno
proven to support over 600 Horsepower. ALL 1994-2000
3.8L V6 Mustangs and 94-95 Mustangs share the EXACT
same air meter and air filter assembly. Testing involving the
replacement of the stock air meter with the stock air filter assembly in place showed
inconsistent results because of air leaks between the filter and meter section.
Using a '99 model V6 test vehicle with an automatic transmission, we were able to
measure a 0-60 improvement of 2 tenths of a second and you can expect anywhere
between 7-10 more horsepower at the rear wheels. Owners of 2001-2004 V6
Mustangs can expect around 12 more horsepower at the rear wheels while 1994-
1995 Mustang 5.0 and Cobras will typically receive 12 more rear wheel horsepower
over the stock air meter and filter assembly. This package comes complete with
everything that you need to replace your factory mass air meter and air filter
assembly.
It includes:
designed for 1994-1995 Mustang 5.0L and 1994-2004 V6
3.8L Mustangs. With 700 CFM of airflow, compared to only
550 CFM of the stock unit it replaces, it has been dyno
proven to support over 600 Horsepower. ALL 1994-2000
3.8L V6 Mustangs and 94-95 Mustangs share the EXACT
same air meter and air filter assembly. Testing involving the
replacement of the stock air meter with the stock air filter assembly in place showed
inconsistent results because of air leaks between the filter and meter section.
Using a '99 model V6 test vehicle with an automatic transmission, we were able to
measure a 0-60 improvement of 2 tenths of a second and you can expect anywhere
between 7-10 more horsepower at the rear wheels. Owners of 2001-2004 V6
Mustangs can expect around 12 more horsepower at the rear wheels while 1994-
1995 Mustang 5.0 and Cobras will typically receive 12 more rear wheel horsepower
over the stock air meter and filter assembly. This package comes complete with
everything that you need to replace your factory mass air meter and air filter
assembly.
It includes:
- C&L 700cfm 73mm non-flanged unit with the appropriate calibration installed
- Rubber adapter sleeve for the rear of the air meter
- 9" conical K&N air filter
- Plastic heat shield that covers the air filter and draws COLD AIR in from the
fender - Installation instructions
- Installation tool
| UPR PRODUCTS |
- 5.0L Aluminum Cold Air Kit
- No cheap, plated mild steel kit here only Polished Aluminum
- Easy 30 Minute Install
- Weighs less than our competitors mild steel kits
- Includes re-useable high flow filter
- Polished Finish
Get the most power out of your 1994-1995 Ford Mustang GT 5.0L with UPR's
Finderwell Cold Air Intake Kit. Features an polished aluminum intake tube for the best
airflow and air intake charge amongst our competitors. Includes a Hi-flow lifetime re-
useable air filter. Moves the air filter into the fender away from the heat of your engine.
Our Quality & Finish will leave you with a grin from ear to ear as it is the Best looking
unit available for your Ford Mustang.
Quality Construction:
Made from Aluminum mandrel bent aluminum tubing then highly polished for an
amazing finish. Most of our competitor kits are mild steel and plated which end up
chipping over time and weigh more. Aluminum construction means lighter, better heat
dissipation and a great look that will last.
*Mass air unit not included
Fits these Vehicles:
1994 1995 GT GTS 5.0 Mustang Steeda Roush & Saleen Vehicles.
1994-1995 5.0L Mustang
|
|
|
|
| 76MM Air Induction System Including Inlet Pipe |
Owners of the '94-'95 V8 Mustang and Cobra vehicles have long
needed a complete intake solution to address the key problem
areas in the factory plastic air meter and filter assembly. By
eliminating everything from the throttle body forward, this new
system has been dyno proven to increase horsepower by as
much as 18 over stock and as much as 12HP on vehicles
equipped with complete K&N replacement systems.
This package includes:
The inlet tube is designed for use with intake manifolds that keep the stock throttle
body location. If you intend on using an '89-'93 style intake manifold with adapter,
you must ensure that the throttle body location is unchanged. Otherwise, minor
modifications may be required for proper fit.
needed a complete intake solution to address the key problem
areas in the factory plastic air meter and filter assembly. By
eliminating everything from the throttle body forward, this new
system has been dyno proven to increase horsepower by as
much as 18 over stock and as much as 12HP on vehicles
equipped with complete K&N replacement systems.
This package includes:
- C&L inlet assembly
- Specially calibrated 76mm MAF unit
- K&N filter assembly
- Plastic heat shield
- All the necessary fittings for assembly
The inlet tube is designed for use with intake manifolds that keep the stock throttle
body location. If you intend on using an '89-'93 style intake manifold with adapter,
you must ensure that the throttle body location is unchanged. Otherwise, minor
modifications may be required for proper fit.
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| Order/Tech Line: 281-636-7142 MONDAY-FRIDAY 9AM-5PM CST |
